How To Reduce Machine Downtime

How To Reduce Machine Downtime

Published On: November 20, 2026-Categories: Equipment Reliability-
aerial view of a car factory

When your machinery stops working, even the shortest interruption can have a significant impact on production. Two minutes can become twenty minutes, then end in a four-hour breakdown. This lost production time will quickly affects schedules and your ability to meet customer commitments.

When these problems arise, it is often tempting to invest in new machinery or expensive equipment upgrades in the hope of improving reliability. However, this isn’t always the most effective solution. In many cases, there are opportunities to reduce machine downtime by improving how existing equipment is maintained and how teams respond to breakdowns.

The key is to focus on two things: getting machinery back up and running as quickly as possible when a breakdown occurs, and preventing the same problems from happening again. Both are important, but they require different approaches.

Two measures can help you understand where improvements are needed: Mean Time to Repair (MTTR) and Mean Time Between Failures (MTBF). Understanding what they tell you is a useful starting point when looking at how to reduce machine downtime.

What is Mean Time to Repair?

Mean Time to Repair (MTTR) measures the average time it takes to repair equipment and restore it to working condition after a failure. In simple terms, it tells you how long your machinery is out of action when something goes wrong. A lower MTTR generally means that machinery can be returned to operation more quickly, reducing the production time lost to breakdowns. However, an average can hide significant differences between short interruptions and longer repairs.

What is Mean Time Between Failures?

In contrast, Mean Time Between Failures (MTBF) measures the average operating time between equipment failures. It gives you an indication of how reliably your machinery is performing and how frequently breakdowns occur. A higher MTBF indicates that machinery is running for longer periods without breaking down. Improving MTBF therefore involves identifying and addressing the recurring causes of equipment failure, rather than simply getting better at repairing problems when they occur.

3 steps to reduce machine downtime

1. Look at the time from stop to first good part

In our experience, the time spent repairing a machine is only part of the production loss. This means that, to understand how to reduce machine downtime and how much time is really lost, you need to map the full time from the machine stopping until the first good part is produced. That can include detecting the stop, making the first diagnosis, calling for support, waiting for a response, investigating, repairing, restarting and confirming quality.

MTTR varies between teams, shifts and areas. It is also affected by how Production and Maintenance work together. Smaller stops can consume a surprising amount of time when the repair and recovery steps are not recorded. A single average may hide where the time is going.

For example, we have seen teams improve their response to breakdowns by agreeing exactly when Production should call Maintenance. After two minutes, Production gave a warning: “We have a stop. We’re checking it.” If the machine was still down ten minutes later, Production confirmed the call and Maintenance came to respond. Maintenance had time to prepare, while Production continued the first checks. The important part was the agreement, not the exact timing.

A useful way to identify where time is being lost is to map the recovery process with Production and Maintenance using post-it notes. Mark each step from the stop to the first good part, then list what standard, form, tool or procedure supports it. A simple red, amber and green review can show where no standard exists, where it is incomplete or ineffective, and where people know and can use it. The mapping and review can be done in about two hours.

2. Reduce the repeated stops

Getting machinery back up and running faster is important, but preventing breakdowns in the first place can have an even greater impact on overall downtime.

One way our manufacturing consultants explain this is with a simple bar chart: each bar represents the duration of a successive breakdown. Shaving the top off each bar represents faster recovery and lower MTTR. Crossing out bars after root-cause analysis represents failures that no longer occur and a longer MTBF.

Shortening every breakdown helps. However, eliminating the cause of several breakdowns can remove more total downtime than making each repair a little quicker. The chart helps the team compare these two opportunities without treating them as the same action.

3. Make the learning part of the standard

Identifying why a breakdown happened is only useful if you act on what you’ve learned. Root-cause analysis is incomplete if it ends with an explanation. It should lead to a countermeasure and to any necessary updates in the way the work is done. This could mean changing preventive maintenance, clarifying equipment operation by operators, creating a One Point Lesson or updating a response procedure. Train the people who need to use the change and check whether the recurrence has stopped.

The aim is shared understanding between Production and Maintenance: what happens during an intervention, what each person needs and what comes next. This reduces frustration and gives the team a clearer route to improving the time from breakdown to the first good part.

A practical starting point

To put this knowledge of how to reduce machine downtime into practice, start by choosing one machine function with repeated interruptions. Agree what counts as the stop and the first good part, then map the elapsed recovery time with Production and Maintenance. At the same time, look for repeat failures that root-cause work could eliminate. Track both: time to recovery and whether the breakdown returns.

Reducing machine downtime requires more than improving the speed of individual repairs. You also need to understand why equipment keeps failing, whether maintenance procedures are effective and how confidently your team can respond when problems occur.

At Primus Passus Consulting, our Equipment Reliability support can help you connect the recovery process, maintenance standards and operator capability to the production flow the business needs to protect. Our manufacturing consultants work with your teams to identify where time is being lost, strengthen maintenance standards and address the underlying causes of repeated failures. Whether you’re dealing with frequent stoppages or lengthy recovery times, we can help you make improvements that support more consistent performance. Get in touch today to find out more. 

Go to Top